■ AV501 needle dispensing valve (for filler) 





 * Pneumatic dispensing valve, the air pressure valve will open more than 0.40MPa. Not only high viscosity materials containing fillers are also applicable to low-medium viscosity materials, and powerful performance. 

 * Suitable materials. 

 * Solder paste, epoxy, containing fillers epoxy, other resins. 









 ■ Standard Specifications 
 Valve structure needle valve way 
 Minimum spit out the amount of 0.01mL 
 Traffic (KV value) 4L/min. 
 Applicable viscosity 1 ~ 500,000 mPa? S 
 Material of wetted parts SUS304, polypropylene, polyamide 
 Material handling pressure-force 686kPa 
 Piping connected 続 the mouth IN.PT1 / 4 
 Actuation speed 150cycles/min the 
 Actuation pressure-power 392 ~ 686kPa 
 Dimensions (□) 30 × (H) 151.5mm 
 Weight 440g 



 ■ AV202A partition dispensing valve 




 * Partition dispensing valves can be divided into electromagnetic drive and pressure-driven in two ways. The pressure-driven approach is to use pressure 343kPa more than to open the valve to open the internal spring to close the valve. 

 * Suitable materials. 

 * Photoresist, rehydration salts, chemicals, food additives, cosmetics, and other low-viscosity materials. 



 Standard 

 Valve constructed bulkhead valve way 
 Minimum spit out the amount of 0.01mL 
 Traffic (KV value) 0.3L/min. 
 Applicable viscosity 1 ~ 1,000 mPa? S 
 Then liquid Ministry Material PTFE, PCTFE 
 Material handling pressure-force 196kPa 
 Piping connected 続 mouth IN.M6 × 1.0 
 Movement speed 200cycles/min 
 Operating pressure 343 ~ 686kPa 
 Dimensions (□) 22 × (H) 78mm 
 Weight 85g 



 Partition dispensing valve can be divided into electromagnetic drive and pressure-driven in two ways. The pressure-driven approach is to use pressure 343kPa more than to open the valve to open the internal spring to close the valve. 


 Standard 

 Applicable to materials 
 ? Photoresist, rehydration salts, chemicals, food additives, cosmetics, and other low-viscosity materials. 



 ■ AV502 needle dispensing valve 


 * Needle dispensing valves are compressed air-driven approach. Kai is more than 392kPa pressure and rely on the internal spring to close the valve. Using a wide range of needle dispensing valves, Both high viscosity materials, including packing materials, low viscosity materials can be dispensing. 

 * Suitable materials 

 * Epoxy, glue and resin. 



 Standard 
 Valve structure needle valve way 
 Minimum spit out the amount of 0.01mL 
 Traffic (KV value) 1.3L/min. 
 Applicable viscosity 1 ~ 300,000 mPa? S 
 Material of wetted parts SUS304, polypropylene, polyamide 
 Material handling pressure-force 490kPa 
 Piping connected 続 mouth IN.PT1 / 8 
 Movement speed 150cycles/min 
 Action-pressure force of 392 ~ 686kPa 
 Dimensions (□) 22 × (H) 84mm 
 Weight 140g 



 ■ AV801 needle dispensing valve 



 * Corresponding to the anaerobic material the AV801 type dispensing valve. Wetted parts are to take the resin material, good anaerobic. 

 Applicable to materials 

 Anaerobic glue, UV glue, cyano glue. 

 Standard 
 Valve constructed needle way 
 Minimum spit out the amount of 0.01mL 
 Traffic (KV value) 1.3L/min. 
 Applicable viscosity 1 ~ 300,000 mPa? S 
 Material of wetted parts PTFE, POM, polyethylene 
 Material handling pressure-force 490kPa 
 Piping connected 続 port IN. PT1 / 8 
 The Bitmap movement speed 
 150cycles/min 
 Action-pressure force of 392 ~ 686kPa 
 Dimensions (□) 22 × (H) 85mm 
 Weight 100g 



 Standard subsidiary parts 
 Description Quantity 
 AV501-10 seat 1